Just got my new Keteles K800 Dual Motor E-bike - Yolin Display Codes?

Hozer said:
I think you are correct. Because of my specs:
"48V" power supply ( Battery ) 30mA Controller

I want to thank all of you guys for the help!! You guys are awesome.

Thanks again :)
Click to expand...
No problem. I got the same display, just a different bike.
20231006_140022.jpg
 
Hozer said:
I think you are correct. Because of my specs:
"48V" power supply ( Battery ) 30mA Controller

I want to thank all of you guys for the help!! You guys are awesome.

Thanks again :)
Click to expand...
Also make sure to physically check your controller max amperage. Cause this display will let you program the maximum amperage higher than your controller can handle.
 
Hozer said:
Just got my new Keteles K800 Dual Motor E-bike, I have a Yolin Display. what do these mean and what they do. here is a list of the P codes:

P01=003
P02=000
P03=048
P04=010
P05=005
P06=29.0
P07=086
P08=100
P09=000
P10=002
P11=001
P12=005
P13=005
P14=012
P15=?
P16=002
P17 = 00
P18 =01

Thanks in advance
Click to expand...
What did you pay? I saw on Yahoo this afternoon that Keteles for $59. Yes $59!
 
UPDATE!!!

The manual YL81F does not seem to be correct for my Keteles K800 With Dual Motors. Example: The Manual sez PAS is P03. When I goto my settings it sez 48. Which is "VOLTAGE"

I just got these new settings and they seem to match what is on my display. I went to P03 on my display and it matched what I have below! Here they are:

P01=003 (back light level)
P02=000 (KMH or MPH)
P03=048 (voltage)
P04=010 (screen timeout 10 minutes)
P05=005 (first number = when the motor helps 0 or 1, 5 = levels)
P06=29.0 (tire size)
P07=086 (? Not sure)
P08=100 (speed limit in kmh)
P09=000 (0 motor helps immediately when you peddle)
P10=002 (0 is pedal assist only, no throttle, 1 is throttle only, 2 is both)
P11=001 (sensitivity of peddle assist 1-24, 1 is the highest)
P12=005 (intensity of power delivery 1-5, 1 is the most)
P13=005 (number of magnets on crank sensor 5,8 or 12)
P14=012 (max amp draw of controller)
P15=38.0 (under voltage cutoff, 38v vs. 48v)
P16=002 (reset ODO, hold mode button and ODO returns to 0)
P17 = 00 (cruise control)
P18 =01 (walk boost)

hope this helps!
 
Hozer said:
UPDATE!!!

The manual YL81F does not seem to be correct for my Keteles K800 With Dual Motors. Example: The Manual sez PAS is P03. When I goto my settings it sez 48. Which is "VOLTAGE"

I just got these new settings and they seem to match what is on my display. I went to P03 on my display and it matched what I have below! Here they are:

P01=003 (back light level)
P02=000 (KMH or MPH)
P03=048 (voltage)
P04=010 (screen timeout 10 minutes)
P05=005 (first number = when the motor helps 0 or 1, 5 = levels)
P06=29.0 (tire size)
P07=086 (? Not sure)
P08=100 (speed limit in kmh)
P09=000 (0 motor helps immediately when you peddle)
P10=002 (0 is pedal assist only, no throttle, 1 is throttle only, 2 is both)
P11=001 (sensitivity of peddle assist 1-24, 1 is the highest)
P12=005 (intensity of power delivery 1-5, 1 is the most)
P13=005 (number of magnets on crank sensor 5,8 or 12)
P14=012 (max amp draw of controller)
P15=38.0 (under voltage cutoff, 38v vs. 48v)
P16=002 (reset ODO, hold mode button and ODO returns to 0)
P17 = 00 (cruise control)
P18 =01 (walk boost)

hope this helps!
Click to expand...
If that is a 48 volt system I would set your low voltage cutoff up a bit. I would set it to 40 or 41volts minimum. It wont tax your battery soo bad. These are just my opinions, as I'm new to ebikes.
 
DieselTech said:
If that is a 48 volt system I would set your low voltage cutoff up a bit. I would set it to 40 or 41volts minimum. It wont tax your battery soo bad. These are just my opinions, as I'm new to ebikes.
Click to expand...
Ya I did set my cutoff at 40. My setting are different than that is listed. Example: it sez wheels size is 29inch. I have 26 in bike. So I set my wheel size to 26.
 
Display "function setting" is matched to the settings that the Controller is setup for.

A XYZ** display can be programmed in 100's of different ways to match controller function.

Thanks for cricling back with the correct Setting that do work for your eBike - that accurate info could be very helpful to someone here down the road
 
fabbrisd said:
Display "function setting" is matched to the settings that the Controller is setup for.

A XYZ** display can be programmed in 100's of different ways to match controller function.

Thanks for cricling back with the correct Setting that do work for your eBike - that accurate info could be very helpful to someone here down the road
Click to expand...
Your Welcome Bud! Just a remember the update settings are for my Keteles K800 Dual motor.
 
fabbrisd said:
Display "function setting" is matched to the settings that the Controller is setup for.

A XYZ** display can be programmed in 100's of different ways to match controller function.

Thanks for cricling back with the correct Setting that do work for your eBike - that accurate info could be very helpful to someone here down the road
Click to expand...
Well I just got a replay from Keteles with pics and they said I should "NOT" make any changes to the display. I am getting different answers from Keteles Tech support. I starting to think that their tech support sucks!!
 
Well - this chase started about helping you to get into "Advance Settings" that were available on your Display/Controller combination.

Now - you can getin there and change values in P01-P18 - all to the good !

You don't want to go further than that - like Ketl says using a PC to re-program the display easily gets wiggy and can knock out your rig.

Keep the beat !
 
fabbrisd said:
Well - this chase started about helping you to get into "Advance Settings" that were available on your Display/Controller combination.

Now - you can getin there and change values in P01-P18 - all to the good !

You don't want to go further than that - like Ketl says using a PC to re-program the display easily gets wiggy and can knock out your rig.

Keep the beat !
Click to expand...
I like the help I got from all of you guys but example the tire size was set at 29 I had to go set it at 26. So I just wish that the info on the display was a crap load better lol.
 
There are a couple other bikes that are essentially the same. The ZEEGR S1/SMLRO and the Philodo.
You can search for those models to gain additional insight. They all use two motors of 1kw and (typically) use the same display (in the current version). I think they all have a 48v 24.4 AH battery with a 50 Amp BMS. Some of the earlier versions did not have a rear suspension.

I have my wheels set to 29 inches, and they match my GPS for speed within 1/10th MPH.
Remember, your RIMS are 26 inches, but your fat tires add to the overall diameter.
This is why the default number used on most these bikes is 29 inches.
 
Back
Top