Download Bafang configuration software

[MarkRT]

How do i download software to reprogram my BBS01 device

 

[Digitol]

E-Bike Conversion – Software

It’s been a while since I wrote the posts about my electric bicycle conversion project. The bicycle runs fine so far and I finally finished rewriting the software that configures its controll…

penoff.me

 

[Albygreat]

I have several bafang bbs02 mid drives that i would like to program. I tried downloading the software from Luna’s website, but I can’t read it, is there a software download for win 11?

 

[J T M Jansen]

I have several bafang bbs02 mid drives that i would like to program. I tried downloading the software from Luna’s website, but I can’t read it, is there a software download for win 11?

Both the Luna software (Penofs rewrite) and Penofs own version work under windows 10 and 11, but note that Penofs own version has some preset limits in it, for safety, if you know what you are doing the Luna one is great.
The download version available on this site requires that you login then download

Bafang 8Fun Programming Software & Guide (BBS02, BBSHD)

How to Program your Bafang Controller - Step by Step Guide (2021) Warning: Using This Software Can Void Your Warranty! ONLY CONTINUE IF YOU ACCEPT THE CONSEQUENCES OF YOUR ACTIONS! If you own a Bafang mid-drive motor you may want to change a...

ebikesforum.com

 

[Albygreat]

Thanks for the advice, I finally got the software loaded and took my first shot at programming, it went well. Now I want to do some advance programming, so can i have assist levels at predetermined % and the throttle in the same PAS level be higher? For example if I had PAS 5 at 65% could I have throttle in PAS 5 at 80% like having a boost without changing gears or PAS levels

 

[J T M Jansen]

Firstly you should set up your BASIC settings pas 1-9 incrementally say from 10-100% CURRENT and SPEED LIMITS.
You can then set your throttle at any of the 1-9 pas settings you set up on the BASIC tab, so if *)% is on pas 8 then set throttle to pas 8.
I will attach my maps so you can get some ideas, but BEWARE, there are differences to BBS01 BBS02 BBS02B and BBS1000HD motor controllers, they all have different MOSFETS in them and can be blown/overloaded, so be careful what you change, I run a BBS02B 350W with 48V x 10.5AH battery and a BBS02B 750w with 48v x 17.5AH battery, you will notice on my 750W model (Program attached) that whilst it has 25AMP controller I have limits set way below for safety. (on my other 350w motor with 10.5ah battery my current limits are a step down again.
As a matter of interest, I have no set limits in any BASIC pas, and my THROTTLE at pas 5 (50% current ) is ample to get me up most hills in my neck of the woods
IF you are unsure what you are doing I suggest you download PENOFS own programmer which has some SET LIMITS you cant override

 

[CADROS]

Buenas como configuro mi motor Bafang BBS01B 36V 250W QC Pass, lo he intentado con Bafangs tool y un cable USB pero no lo reconoce, hace poco se me tosto el controldor que venia de fabrica y me mandaron uno nuevo, todo bien pero no se porque no puedo entrar a la configuración Del motor no lo lee.



MODERATOR EDIT/TRANSLATION:

Good how I configure my Bafang BBS01B 36V 250W QC Pass motor, I have tried it with Bafangs tool and a USB cable but it does not recognize it, recently the controller that came from the factory was roasted and they sent me a new one, all good but I do not know why I can not enter the configuration of the motor it does not read it.