bafang

Bafang 21H error, no speed displayed or mileage either And the power/display turns off irregular intervals, 1 mile, 3 miles ? Thanks

Hello. This is my first post to the forum. I have just converted my old mtb to an eBike using the above kit. It's 90% complete and I am now trying to check and reset some of the settings in the controller and having a problem connecting to the controller. I am using the LUNA programming...

Hi all, New to this forum and new to ebikes. I have a Nihola cargo tricycle that has had a Bafang conversion done. It is a second hand bike. It is fitted with a generic 48V lithium battery. Basically when the battery is charged, everything works, but once it drops to 48-49V, it starts...

Hi, I'm looking to the wiring diagram(pinout) for a bafang ebike motor with an 11 pin julet connector. Also, looking for a contoller that uses the 11 pin julet connector for the banfang motor. Thanks

So the real high-end fully-built cargo e-bikes, such as the urban arrow, the extracycle bikes, yuba... all come with either the shimano or the bosch mid-drives. I have been told by every salesperson that they are "the best". Of course i can't help but notice these mid-drives are HALF, (perhaps...

Hi everyone, I have a weird problem with my Bafang M600 mid drive and I am wondering if anyone could help me figure out whats wrong or if someone already had the same issue. when I give the pedals a sharp push, they spin without tension without having to roll the wheels as normal behavior. It's...

Will a battery with the following specs work with the 1000w 52v Bafang BBSHD- I am scared that 60A constant discharge current is too much? Nominal Volt: 52V Rated Capacity: 40AH Max Constant Discharge Current: 60A Peak current: 120A

Hello Has anyone tried to install a front and a rear light using the 6v output from the Bafang BSS0HD motor, hooking it up in parallel, will it drive both lights or just one..??!! Thanks

Interested in selling a 100% unused, uninstalled Bafang BBSHD Mid Drive Ebike Kit with several additional upgrades and accessories. This is the "Hot Rod" version from Luna Cycles. This will only fit bikes with a bottom bracket size of 68mm (the most common for road and mtb). This will not fit...

I am newer to ebike repairs. I have a G510/M620 Bafang motor, I regreased the motor gears and put back together and one wire pinched (tempature), I was able to start and ride it, after shutting off it wouldnt start again. I repaired the tempature wire but still doesnt start. I could use some...

Hello everyone My project started with a wish of a small adjustment. At least I thought so! o_O I bought a new e-bike with a middrive Bafang M200. I did some research and bought the BESST tool as my bike has CANBUS. The seller provide login which works to both Besst and Besst Pro software. I...

I'd gotten a bad throttle error. I replaced the throttle that tested good on my wife's bile. The display suggests everything's hunky-dory, but I get nothing. I've also replaced the seller-supplied controller. I'm just trying to eliminate as much as possible, including sudden motor failure...

Does anyone know how to replace the teeth inside the hub? The bike will make noise and then a grinding sound when the throttle is pushed. The planetary gears are fine. We think those internal teeth are moving when the throttle is pushed. Thanks in advance!

Hi all, installed the above motor setup on a Trek X-Calibur 8 about a month ago to be a spare for my daily rider. No issues until 200 km when I was going up a steep hill, there was a loud bang from the direction of the motor and battery. Screen blank, had to push her! 30 A fuse blown in...

Bafang Motor Reprogramming Help Hi All, I'm having a problem with the a bafang motor I just purchased. I recently bought a new recumbent trike and equipped it with a 750w BBS02. I find the settings out of the box to be fairly unusable. As i like to bike tour I tend to make settings that draw...

Bafang Motor Reprogramming Help Hi All, I'm having a problem with the a bafang motor I just purchased. I recently bought a new recumbent trike and equipped it with a 750w BBS02. I find the settings out of the box to be fairly unusable. As i like to bike tour I tend to make settings that draw...

"Hello, I have a Bafang BBS-HD 48V 1000W motor. It was working properly, but then it started giving an error code 30h and didn't move. I found out that in this video, a person fixed this problem by installing new firmware, which I also did. However, I suspect that I may have done something wrong...

Hello everyone, New to the forum. I am converting a Sunseeker Fat Tad. I have decided to install a 750w mid drive. It arrives on Tuesday.

Hi all! I am new to the wonderfull world of DIY ebikes and excited to be part of this community! However, I am not posting today for a very good reason :/ 2 weeks ago I have installed a Bafang BBS02B 48 V 750 W with DM03 Display on a brand new commuter bike I have bought specifically for this...

Please help Does anybody have this problem where after riding a while and your motor stops responding DPC 18 display Bafang 750w 48v